Flash your DV-Mega from Pi-Star
From PiStar Wiki
Jump to navigationJump to search1. Login to your Pi-Star over SSH (either on your PC using an SSH client or using the built-in client available at http://pi-star.local/admin/expert/ssh_access.php
2. Change to the /tmp folder
[email protected]mr(rw):~$ cd /tmp
3. Download the flashing tool(s)
[email protected](rw):tmp$ wget http://www.pistar.uk/downloads/dvmega-flash-tools.zip --2017-11-22 21:36:38-- http://www.pistar.uk/downloads/dvmega-flash-tools.zip Resolving www.pistar.uk (www.pistar.uk)... 104.27.185.136, 104.27.184.136, 2400:cb00:2048:1::681b:b888, ... Connecting to www.pistar.uk (www.pistar.uk)|104.27.185.136|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 851 [application/zip] Saving to: ‘dvmega-flash-tools.zip’ dvmega-flash-tools.zip 100%[=========================================================>] 851 --.-KB/s in 0s 2017-11-22 21:36:38 (22.1 MB/s) - ‘dvmega-flash-tools.zip’ saved [851/851]
4. Download the DVMega firmware from the download site: http://www.dvmega.auria.nl/Downloads.html
[email protected](rw):tmp$ wget http://www.dvmega.auria.nl/images/DVMEGA_RH_V319_UNO.zip --2017-11-22 21:38:06-- http://www.dvmega.auria.nl/images/DVMEGA_RH_V319_UNO.zip Resolving www.dvmega.auria.nl (www.dvmega.auria.nl)... 89.18.176.53 Connecting to www.dvmega.auria.nl (www.dvmega.auria.nl)|89.18.176.53|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 26419 (26K) [application/zip] Saving to: ‘DVMEGA_RH_V319_UNO.zip’ DVMEGA_RH_V319_UNO.zip 100%[=========================================================>] 25.80K --.-KB/s in 0.03s 2017-11-22 21:38:06 (774 KB/s) - ‘DVMEGA_RH_V319_UNO.zip’ saved [26419/26419]
5. Unzip the firmware and the tools
[email protected](rw):tmp$ unzip -d dvmega dvmega-flash-tools.zip Archive: dvmega-flash-tools.zip inflating: dvmega/flash_gpio.sh inflating: dvmega/flash_usb.sh [email protected](rw):tmp$ unzip -j -d dvmega DVMEGA_RH_V319_UNO.zip Archive: DVMEGA_RH_V319_UNO.zip inflating: dvmega/Changelog.txt inflating: dvmega/DVMEGA_RH_V319_UNO.hex
7. Change to the dvmega subfolder and run the script, for GPIO DV-Mega please use flash_gpio.sh - also note the use of sudo here.
[email protected](rw):tmp$ cd dvmega/ [email protected](rw):dvmega$ sudo ./flash_gpio.sh
8. You should get an output similar to:
Warning: Stopping pistar-watchdog.service, but it can still be activated by:
pistar-watchdog.timer
Warning: Stopping dstarrepeater.service, but it can still be activated by:
dstarrepeater.timer
Found DVMEGA_RH_V319_UNO.hex firmware...
avrdude-original: Version 6.1, compiled on Jul 7 2015 at 10:29:47
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/root/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyAMA0
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude-original: Using autoreset DTR on GPIO Pin 7
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us
avrdude-original: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude-original: Device signature = 0x1e950f
avrdude-original: safemode: lfuse reads as 0
avrdude-original: safemode: hfuse reads as 0
avrdude-original: safemode: efuse reads as 0
avrdude-original: NOTE: "flash" memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude-original: erasing chip
avrdude-original: reading input file "DVMEGA_RH_V319_UNO.hex"
avrdude-original: input file DVMEGA_RH_V319_UNO.hex auto detected as Intel Hex
avrdude-original: writing flash (32074 bytes):
Writing | ################################################## | 100% 4.59s
avrdude-original: 32074 bytes of flash written
avrdude-original: verifying flash memory against DVMEGA_RH_V319_UNO.hex:
avrdude-original: load data flash data from input file DVMEGA_RH_V319_UNO.hex:
avrdude-original: input file DVMEGA_RH_V319_UNO.hex auto detected as Intel Hex
avrdude-original: input file DVMEGA_RH_V319_UNO.hex contains 32074 bytes
avrdude-original: reading on-chip flash data:
Reading | ################################################## | 100% 3.39s
avrdude-original: verifying ...
avrdude-original: 32074 bytes of flash verified
avrdude-original: safemode: lfuse reads as 0
avrdude-original: safemode: hfuse reads as 0
avrdude-original: safemode: efuse reads as 0
avrdude-original: safemode: Fuses OK (E:00, H:00, L:00)
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
strace: |autoreset: Broken pipe
avrdude-original done. Thank you.
strace: |autoreset: Broken pipe
Once flashing has been completed, you should reboot your Pi-Star
Please note that the Broken Pipe(s) at the end are normal.
